TL16C754CTIThe 754C is a quad universal asynchronous receiver/transmitter (UART) with 64Byte FIFOs, automatic hardware/software flow control, and data rates up to 3Mbps
￥
0
显示的图像仅供参考，应从产品数据表中获得准确的规格。
TL16C754CTI
制造商:
TI
制造商型号#:
TL16C754C
百芯编号#:
CM435389133
价格(CNY):
百芯库存:
236
个
库存地点:
可供应量:
164
个在库
此为供应商库存，需要与销售确认
产品描述:
The 754C is a quad universal asynchronous receiver/transmitter (UART) with 64Byte FIFOs, automatic hardware/software flow control, and data rates up to 3Mbps
The 754C is a quad universal asynchronous receiver transmitter (UART) with 64-byte FIFOs, automatic hardware and software flow control, and data rates up to 3 Mbps. It incorporates the functionality of four UARTs, each UART having its own register set and FIFOs. The four UARTs share only the data bus interface and clock source, otherwise they operate independently. Another name for the UART function is Asynchronous Communications Element (ACE), and these terms are used interchangeably. The bulk of this document describes the behavior of each ACE, with the understanding that four such devices are incorporated into the 754C. The 754C offers enhanced features. It has a transmission control register (TCR) that stores received FIFO threshold level to start or stop transmission during hardware and software flow control. With the FIFO RDY register, the software gets the status of TXRDY/RXRDY for all four ports in one access. On-chip status registers provide the user with error indications, operational status, and modem interface control. System interrupts may be tailored to meet user requirements. An internal loopback capability allows onboard diagnostics.
Each UART transmits data sent to it from the peripheral 8-bit bus on the TX signal and receives characters on the RX signal. Characters can be programmed to be 5, 6, 7, or 8 bits. The UART has a 64-byte receive FIFO and transmit FIFO and can be programmed to interrupt at different trigger levels. The UART generates its own desired baud rate based upon a programmable divisor and its input clock. It can transmit even, odd, or no parity and 1-, 1.5-, or 2-stop bits. The receiver can detect break, idle or framing errors, FIFO overflow, and parity errors. The transmitter can detect FIFO underflow. The UART also contains a software interface for modem control operations, and software flow control and hardware flow control capabilities.
The 754C is available in a 64-pin TQFP PM package. RXRDY and TXRDY functionality is not supported in the TL16C754CPM device.
ST16C654/654D Pin Compatible With Additional Enhancements
Support up to:
24-MHz Crystal Input Clock (1.5 Mbps)
48-MHz Oscillator Input Clock (3 Mbps) for 5-V Operation
32-MHz Oscillator Input Clock (2 Mbps) for 3.3-V Operation
24-MHz Input Clock (1.5 Mbps) for 2.5-V Operation
16-MHz Input Clock (1 Mbps) for 1.8-V Operation
64-Byte Transmit FIFO
64-Byte Receive FIFO With Error Flags
Programmable and Selectable Transmit and Receive FIFO Trigger
Levels for DMA and Interrupt Generation
Programmable Receive FIFO Trigger Levels for Software/Hardware
Flow Control
Software/Hardware Flow Control
Programmable Xon/Xoff Characters
Programmable Auto-RTS and Auto-CTS
Optional Data Flow Resume by Xon Any Character
RS-485 Mode Support
Support 1.8-V, 2.5-V, 3.3-V, or 5-V Supply
Characterized for Operation From –40°C to 85°C,
Available in Commercial and Industrial Temperature Grades
Software-Selectable Baud-Rate Generator
Prescaler Provides Additional Divide-by-4 Function
Programmable Sleep Mode
Programmable Serial Interface Characteristics
5-, 6-, 7-, or 8-Bit Characters
Even, Odd, or No Parity Bit Generation and Detection
1-, 1.5-, or 2-Stop Bit Generation
False Start Bit Detection
Complete Status Reporting Capabilities in Both Normal and Sleep Mode
Line Break Generation and Detection
Internal Test and Loopback Capabilities
Fully Prioritized Interrupt System Controls
Modem Control Functions (CTS, RTS, DSR, DTR, RI, and CD)
