Datasheet
数据手册 > 微控制器,MCU,单片机 > Microchip > PIC18F14K22-E/ML 数据手册PDF > PIC18F14K22-E/ML 用户编程手册 第 1/36 页
PIC18F14K22-E/ML
¥ 5.11
百芯的价格

PIC18F14K22-E/ML 用户编程手册 - Microchip

更新时间: 2024-10-31 22:19:35 (UTC+8)

PIC18F14K22-E/ML 用户编程手册

页码:/36页
下载 PDF
重新加载
下载
© 2009 Microchip Technology Inc. Advance Information DS41357B-page 1
PIC18F1XK22/LF1XK22
1.0 DEVICE OVERVIEW
This document includes the programming
specifications for the following devices:
2.0 PROGRAMMING OVERVIEW
The PIC18F1XK22/LF1XK22 devices can be
programmed using either the high-voltage In-Circuit
Serial Programming™ (ICSP™) method or the low-
voltage ICSP method. Both methods can be done with
the device in the users’ system. The low-voltage ICSP
method is slightly different than the high-voltage
method and these differences are noted where
applicable. The PIC18F1XK22 devices operate from
1.8 to 5.5 volts and the PIC18LF1XK22 devices
operate from 1.8 to 3.6 volts. All other aspects of the
PIC18F1XK22 with regards to the PIC18LF1XK22
devices are identical.
2.1 Hardware Requirements
In High-Voltage ICSP mode, the PIC18F1XK22/
LF1XK22 devices require two programmable power
supplies: one for V
DD and one for MCLR/VPP/RA3.
Both supplies should have a minimum resolution of
0.25V. Refer to Section 8.0 “AC/DC Characteristics
Timing Requirements for Program/Verify Test
Mode” for additional hardware parameters.
2.1.1 LOW-VOLTAGE ICSP
PROGRAMMING
In Low-Voltage ICSP mode, the PIC18F1XK22/
LF1XK22 devices can be programmed using a single
V
DD source in the operating range. The MCLR/VPP/
RA3 does not have to be brought to a different voltage,
but can instead be left at the normal operating voltage.
Refer to Section 8.0 “AC/DC Characteristics Timing
Requirements for Program/Verify Test Mode” for
additional hardware parameters.
2.1.1.1 Single-Supply ICSP Programming
The LVP bit in Configuration register, CONFIG4L,
enables single-supply (low-voltage) ICSP
programming. The LVP bit defaults to a ‘1’ (enabled)
from the factory.
If Single-Supply Programming mode is not used, the
LVP bit can be programmed to a ‘0’ and RC3/PGM
becomes a digital I/O pin. However, the LVP bit may
only be programmed by entering the High-Voltage
ICSP mode, where MCLR
/VPP/RA3 is raised to VIHH.
Once the LVP bit is programmed to a ‘0’, only the
High-Voltage ICSP mode is available and only the
High-Voltage ICSP mode can be used to program the
device.
PIC18F13K22 PIC18LF13K22
PIC18F14K22 PIC18LF14K22
Note 1: The High-Voltage ICSP mode is always
available, regardless of the state of the
LVP bit, by applying V
IHH to the MCLR/
V
PP/RA3 pin.
2: While in Low-Voltage ICSP mode, the
RC3 pin can no longer be used as a
general I/O.
Flash Memory Programming Specification
页面指南

PIC18F14K22-E/ML 数据手册 PDF

PIC18F14K22-E/ML 数据手册
Microchip
388 页, 3276 KB
PIC18F14K22-E/ML 用户编程手册
Microchip
36 页, 463 KB
PIC18F14K22-E/ML 其它数据手册
Microchip
19 页, 279 KB
PIC18F14K22-E/ML 产品修订记录
Microchip
2 页, 111 KB

PIC18F14K22 数据手册 PDF

PIC18F14K22-I/SS
数据手册
Microchip
SSOP-20 0.209in TUBE, 16KB Flash, 512Bytes RAM, 256Bytes EEPROM, 16MIPS, 1.8-5.5V
PIC18F14K22-I/SO
数据手册
Microchip
MCU 8Bit PIC18 PIC RISC 16KB Flash 2.5V/3.3V/5V 20Pin SOIC W Tube
PIC18F14K22T-I/ML
数据手册
Microchip
MCU 8Bit PIC18 PIC RISC 16KB Flash 2.5V/3.3V/5V 20Pin QFN EP T/R
PIC18F14K22T-I/SS
数据手册
Microchip
MCU 8Bit PIC18 PIC RISC 16KB Flash 2.5V/3.3V/5V 20Pin SSOP T/R
PIC18F14K22-I/ML
数据手册
Microchip
MCU 8Bit PIC RISC 16KB Flash 2.5V/3.3V/5V Automotive 20Pin QFN EP Tube
PIC18F14K22-I/P
数据手册
Microchip
PDIP-20 0.3in TUBE, 16KB Flash, 512Bytes RAM, 256Bytes EEPROM, 16MIPS, 1.8-5.5V
PIC18F14K22-E/SS
数据手册
Microchip
16KB Flash, 512Bytes RAM, 256Bytes EEPROM, 16MIPS, 1.8-5.5V operation, 20 SSOP 0.209in TUBE
PIC18F14K22T-I/SO
数据手册
Microchip
MCU 8Bit PIC18 PIC RISC 16KB Flash 2.5V/3.3V/5V 20Pin SOIC W T/R
PIC18F14K22-E/ML
数据手册
Microchip
MCU 8Bit PIC18 PIC RISC 16KB Flash 2.5V/3.3V/5V 20Pin QFN EP
PIC18F14K22-E/SO
数据手册
Microchip
MCU 8Bit PIC18 PIC RISC 16KB Flash 2.5V/3.3V/5V 20Pin SOIC W
Datasheet 搜索
搜索
百芯智造数据库涵盖1亿多个数据手册,每天更新超过5,000个PDF文件。
在线联系我们
黄经理 - 百芯智造销售经理在线,5 分钟前
您的邮箱 *
消息 *
发送